How to Fix Sinking Pavers

If you have a sinking paver problem, don’t despair. It is a common issue that can be easily fixed. Learn how to fix sinking pavers here.

Checkout this video:

Introduction

If your pavers have sunken or are starting to sink, don’t despair! It is a common problem that is relatively easy to fix. In this article, we will show you how to fix sinking pavers.

There are several reasons why pavers may sink. The most common reason is that the pavers were not properly installed on a stable base. over time, the weight of the pavers can cause the pavers to sink into the ground. Another common reason for sinking pavers is poor drainage. If water does not drain properly around and under the pavers, the water can wash away the soil supporting the pavers, causing them to sink.

Whatever the reason for your sinking pavers, there are two simple ways to fix them: re-leveling or re-paving.

Re-leveling is a quick and easy way to fix sinking pavers. You will need to rent or purchase a leveling device, such as a paver leveling plate, paver leveling bar, or power vibrating plate compactor. You will also need to have some leveling sand on hand.

To re-level your pavers, start by clearing away any debris around the area where the paVERS ARE sunken. Next, wet down the area with a hose or watering can to help keep dust down while you work. Then, starting at one end of the area, use your leveling device to raise each paver up to its original level. Once all of the PAVERS ARE raised up, brush in some leveling sand around and under each paver until it is evenly distributed and supportive. Finally, mist down the area with water again and allow it to dry completely before using it again (we recommend waiting at least 24 hours).

If your paVERS ARE severely sunken or are in an area with poor drainage, you may want to consider re-paving instead of just re-leveling them. Re-paving is more work than re-leveling but will provide a more permanent solution for severe sinking or poor drainage problems.

When re-paving sunken or poorly drained areas, you will need to remove all of the existing PaVERS FIRST before installing new ones. Once all of tHE old PaVERS ARE removed, use a shovel and rake to level out the area and make sure that it drains well before installing new PaVERS . We recommend compacting soil with a hand tamper before laying down a layer of gravel followed by a layer of sand (for more details on how to install PaVERS , see our article How To Lay PaVERS ). After your new PaVErs ARE installed , be sure tO fill in any joints between them with sand for added stability

Causes of Sinking Pavers

There are many reasons why pavers may sink, but the most common is simply due to poor drainage. If the area where your pavers are installed does not have adequate drainage, over time the weight of the pavers will cause them to sink into the ground. Other causes of sinking pavers include:

– Soil erosion
– Tree roots
– Poorly compacted soil
– Frost heave

Preparation

The first step is to remove any vegetation, including grass, weeds, and roots, from the area where the pavers will be installed. Next, use a shovel to dig up the soil to a depth of about 8 inches. Level off the area with a rake, and then use a tamper or hand-held compactor to compact the soil.

Now you’re ready to install a base layer of gravel. This should be done in two steps: first, spread a layer of coarse gravel over the entire area; then, spread a layer of fine gravel over the coarse layer. Use a rake to level off the gravel, and then compact it with a tamper or hand-held compactor.

Once the base is prepared, you can start installing the pavers. Begin by spreading a layer of sand over the entire area. The sand should be no more than 1 inch thick. Next, lay the pavers in your desired pattern; make sure to leave about ¼ inch between each paver for jointing material.

After all of the pavers are in place, brush jointing sand into all of the joints between the pavers. Use a broom with stiff bristles to work the sand into the joints until they’re full. Finally, compact the entire surface with a vibrating plate compactor to set the pavers in place.

Materials Needed

You will need the following materials to fix your sinking pavers:

-Paver Base Panel
-Polymeric Paver Sand
-Shovel
-Wheelbarrow
-Trowel
-Mallet

How to Fix Sinking Pavers

If you have noticed that your pavers have begun to sink, there are a few things that you can do in order to fix the problem. In most cases, sinking pavers are caused by one of two things: either the ground underneath the pavers has shifted, or the pavers were not installed properly in the first place.

If the issue is with the ground shifting, there is not much that you can do on your own to fix the problem. In this case, you will likely need to hire a professional to come and level out the ground for you. This can be a bit of a pricey fix, but it is definitely worth it in order to keep your pavers looking their best.

If the problem is that the pavers were not installed properly, there are a few things that you can do in order to fix sinking pavers. The first thing that you will need to do is remove any loose dirt or sand from around the affected area. Once you have done this, you will need to add more sand or gravel underneath the pavers in order to provide them with additional support. In some cases, you may also need to replace any cracked or broken pavers.

Conclusion

Pavers are a great way to add some character and flair to your outdoor living space. However, they can also be a source of frustration if they start to sink or shift. If you have some sinking pavers, there is no need to despair. With a little elbow grease and some help from a professional, you can get your pavers back in tip-top shape in no time.